MAX14870 - single-channel motor controller 36V/1.7A - Pololu 2961

Бестселлер
47804755
1 744 ₽

Мы сотрудничаем с поставщиками электрики Pololu и предлагаем вам самые выгодные предложения на брендовые товары из Америки. Опираясь на свой многолетний опыт, выбираем только лучшие позиции из аутлетов и дискаунтеров, чтобы предоставить вам оптимальные цены, в которые не включены дополнительные расходы на аренду торговых помещений.

Доставка товаров осуществляется прямо с нашего склада до указанного вами адреса. Вы получаете оригинальный товар по цене, которая недоступна для местных магазинов. В нашем интернет-магазине вы всегда найдете широкий ассортимент брендовых товаров с выгодными скидками.

Мы следим за каждым этапом вашей покупки и предоставляем отслеживание заказа на всех этапах, начиная с момента оплаты.

  • Бренд Pololu
  • Доставка из Польши
  • Пункт выдачи СДЭК 9 июня
  • Стоимость доставки заказа в Россию от 689 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Напряжение от
36 V

Общие характеристики

Напряжение до
4.5 V

Прочие свойства

Бренд
Pololu

Свойства

Каналы
1

Энергопитание

Сила тока
1.7 A

Описание

Description: MAX14870 - single channel 36V/1.7A motor controller

The module based on the MAX14870 Instruments system allows to control one DC motor. The motor can be powered from 4.5 V to 36 V with a continuous current draw of up to 1.7 A, temporary (for a few seconds) to 2.5 A. Before use, we recommend to read thedocumentation ofthe MAX14870.

Polol MAX14870 motor controller specifications
  • Number of channels: 1
  • Supply voltage: 4.5 V to 36 V
  • Continuous current per channel: 1.7 A
  • Maximum instantaneous current per channel: 2,5 A
  • Maximum PWM signal frequency: 50 kHz
  • Reverse power supply protection
  • Dimensions: 15.5 x 13.0 mm
  • Weight: 5 g (without connectors)
  • Included module and goldpin connectors
Connecting the motor controller

In a typical application, it is enough to connect two control lines: DIR direction selection and PWM speed control. By default, the PWM signal on the board is pulled up to ground by a 100 kΩ resistor, so the controller is switched off. If there is no need to use speed control, a high state (logical one) must be specified on the PWM output.

The EN or ENABLE output disconnects the motor outputs. If the high state is given, the M1 and M2 outputs are in high impedance state. The EN is pulled to ground by a 100 kΩ resistor, which means that the circuit is switched on by default.

EN PWM DIR M1 M2 Mode of operation 1 X X

high

impedance

high

impedance

disconnected outputs

idle

0 1 0 GND VIN forward revolutions 0 1 1 VIN GND backwards 0 0 X GND GND

braking

outputs connected to the ground

1 - high state, 0 - low state, X - unconnected output

MAX14870 controller outputs PIN Description Vin Motor supply voltage from 4.5 V to 36 V. GND The mass potential of the system. M1 Outputs + to connect the motor outputs. M2 Outputs - to connect the motor outputs. DIR Logical input defining the direction of engine rotation. PWM Logical input for speed setting. A PWM signal must be connected to this output. Default is low. EN Logical input that switches the system to the sleep state when low state is given. Default is high state. FAULT Logical output indicating error in low state. Not connected by default. Current limitation

The system has the ability to limit the motor current. To do so, cut the path as shown in the drawing:

then solder the resistor in SMD 1206 housing. 100 mΩ resistor will limit current to 1 A, 200 mΩ to 0.5 A etc. See thedocumentationfor details.

Video

Film describing the operation of the H-bridge - direct current motor controller.

Useful links
  • Polol manufacturer's website #2961
  • System documentation MAX14870

Доставка

Мы доставляем товары напрямую из Германии в Россию курьерской службой или в почтовое отделение. Вы можете выбрать подходящий для вас способ доставки при оформлении заказа. Стоимость доставки зависит от выбранного метода и начинается от 689 руб. Время доставки зависит от выбранного города и метода доставки, но в среднем занимает от 10 до 30 дней. Если вы оформите заказ прямо сейчас, мы доставим его в период с 29 мая - 18 июня.

На протяжении уже более 10 лет мы работаем с надежными и проверенными нами службами и предлагаем доставку электрики Pololu в различные города России, такие как  Москва, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие.

Вы всегда можете отследить свой заказ, используя номер посылки, сразу как только он будет отправлен к вам с нашего склада.